| Opcode | Instruction | Op/En | 64-Bit Mode | Compat/Leg Mode | Description |
|---|---|---|---|---|---|
| 0F 02 /r | LAR r16, r16/m16 | RM | Valid | Valid | r16 ← access rights referenced by r16/m16 |
| 0F 02 /r | LAR reg, r32/m161 | RM | Valid | Valid | reg ← access rights referenced by r32/m16 |
NOTES: 1. For all loads (regardless of source or destination sizing) only bits 16-0 are used. Other bits are ignored.
| Op/En | Operand 1 | Operand 2 | Operand 3 | Operand 4 |
| RM | ModRM:reg (w) | ModRM:r/m (r) | NA | NA |
Loads the access rights from the segment descriptor specified by the second operand (source operand) into the first operand (destination operand) and sets the ZF flag in the flag register. The source operand (which can be a register or a memory location) contains the segment selector for the segment descriptor being accessed. If the source operand is a memory address, only 16 bits of data are accessed. The destination operand is a general-purpose register.
The processor performs access checks as part of the loading process. Once loaded in the destination register, soft-ware can perform additional checks on the access rights information.
The access rights for a segment descriptor include fields located in the second doubleword (bytes 4–7) of the segment descriptor. The following fields are loaded by the LAR instruction:
— Bits 19:16 are undefined.
— Bit 20 returns the software-available bit in the descriptor.
— Bit 21 returns the L flag.
— Bit 22 returns the D/B flag.
— Bit 23 returns the G flag.
— Bits 31:24 are returned as 0.
This instruction performs the following checks before it loads the access rights in the destination register:
If the segment descriptor cannot be accessed or is an invalid type for the instruction, the ZF flag is cleared and no access rights are loaded in the destination operand.
The LAR instruction can only be executed in protected mode and IA-32e mode.
| Type | Protected Mode | IA-32e Mode | ||
|---|---|---|---|---|
| Name | Valid | Name | Valid | |
|
0 1 2 3 4 5 6 7 8 9 A B C D E F |
Reserved Available 16-bit TSS LDT Busy 16-bit TSS 16-bit call gate 16-bit/32-bit task gate 16-bit interrupt gate 16-bit trap gate Reserved Available 32-bit TSS Reserved Busy 32-bit TSS 32-bit call gate Reserved 32-bit interrupt gate 32-bit trap gate |
No Yes Yes Yes Yes Yes No No No Yes No Yes Yes No No No |
Reserved Reserved LDT Reserved Reserved Reserved Reserved Reserved Reserved Available 64-bit TSS Reserved Busy 64-bit TSS 64-bit call gate Reserved 64-bit interrupt gate 64-bit trap gate |
No No No No No No No No No Yes No Yes Yes No No No |
IF Offset(SRC) > descriptor table limit
THEN
ZF ← 0;
ELSE
SegmentDescriptor ← descriptor referenced by SRC;
IF SegmentDescriptor(Type) ≠ conforming code segment
and (CPL > DPL) or (RPL > DPL)
or SegmentDescriptor(Type) is not valid for instruction
THEN
ZF ← 0;
ELSE
DEST ← access rights from SegmentDescriptor as given in Description section;
ZF ← 1;
FI;
FI;
The ZF flag is set to 1 if the access rights are loaded successfully; otherwise, it is cleared to 0.
| #GP(0) |
If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit. If the DS, ES, FS, or GS register is used to access memory and it contains a NULL segment selector. |
| #SS(0) | If a memory operand effective address is outside the SS segment limit. |
| #PF(fault-code) | If a page fault occurs. |
| #AC(0) | If alignment checking is enabled and the memory operand effective address is unaligned while the current privilege level is 3. |
| #UD | If the LOCK prefix is used. |
| #UD | The LAR instruction is not recognized in real-address mode. |
| #UD | The LAR instruction cannot be executed in virtual-8086 mode. |
Same exceptions as in protected mode.
| #SS(0) | If the memory operand effective address referencing the SS segment is in a non-canonical form. |
| #GP(0) | If the memory operand effective address is in a non-canonical form. |
| #PF(fault-code) | If a page fault occurs. |
| #AC(0) | If alignment checking is enabled and the memory operand effective address is unaligned while the current privilege level is 3. |
| #UD | If the LOCK prefix is used. |